Reinforcement StraightRebar/ro

Arch CompRebarStraight/ro

UShape Rebar

Arch

Description

This tool is part of the Reinforcement Workbench, an external workbench that can be installed with the Addon Manager.

Cum se folosește

Task panel for the tool

Proprietăți

• DateOrientation: Acesta decide orientarea armăturii (de ex. jos, sus, drepta și stânga).
• DateFront Cover: Distanța dintre armături și fațetele selectate.
• DateRight Cover: Distanța între capătul dintre capătul dreapta al armăturii și fațeta dreapta a structurii.
• DateLeft Cover: Distanța dintre capătul din stânga al armăturii și fațeta stângă a structurii
• DateBottom Cover: Distanța dintre armătură și fațeta de jos a structurii.
• DateTop Cover: Distanța dintre armătură și fața superioară a structurii.
• DateRounding: O valoare de rotunjire care trebuie aplicată colțurilor barelor, exprimată în raport cu diametrul acestora.
• DateAmount: Cantitatea de armătură
• DateSpacing: Distnța dintre acele fiecărei bare.

Scripting

Rebar = makeStraightRebar(f_cover, coverAlong, rt_cover, lb_cover,
                          diameter, amount_spacing_check, amount_spacing_value, orientation="Horizontal",
                          structure=None, facename=None)

• Creates a Rebar object from the given structure, which is an Arch Structure, and facename, which is a face of that structure.
  • If no structure nor facename are given, it will take the user selected face as input.
• f_cover, coverAlong, rt_cover, and lb_cover are inner offset distances for the rebar elements with respect to the faces of the structure.
  • f_cover is the frontal cover offset.
  • coverAlong is a tuple (position, value) that defines the offset value in one position (top, bottom, left, right) depending on the orientation.
  • rt_cover is either the right or the top cover offset, depending on the value of coverAlong and orientation.
  • lb_cover is either the left or the bottom cover offset, depending on the value of coverAlong and orientation.
• diameter is the diameter of the reinforcement bars inside the structure.
• amount_spacing_check if it is True it will create as many reinforcement bars as given by amount_spacing_value; if it is False it will create reinforcement bars separated by the numerical value of amount_spacing_value.
• amount_spacing_value specifies the number of reinforcement bars, or the value of the separation between them, depending on amount_spacing_check.
• orientation specifies the orientation of the rebar; it can be "Horizontal" or "Vertical".

Depending on the orientation of the rebar, the function can be called in two general ways by setting coverAlong appropriately.

The rebar is horizontal

Rebar = makeStraightRebar(f_cover, ("Top Side", value), right_cover, left_cover, ...)
Rebar = makeStraightRebar(f_cover, ("Bottom Side", value), right_cover, left_cover, ...)

• coverAlong is a tuple with either a "Top Side" or a "Bottom Side" offset value.
• In this case rt_cover refers to the right_cover offset, and lb_cover refers to the left_cover offset.

The rebar is vertical

Rebar = makeStraightRebar(f_cover, ("Left Side", value), top_cover, bottom_cover, ...)
Rebar = makeStraightRebar(f_cover, ("Right Side", value), top_cover, bottom_cover, ...)

• coverAlong is a tuple with either a "Left Side" or a "Right Side" offset value.
• In this case rt_cover refers to the top_cover offset, and lb_cover refers to the bottom_cover offset.

Example horizontal

import Arch, Draft, StraightRebar

Structure = Arch.makeStructure(length=1000, width=1000, height=400)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()

Rebar = StraightRebar.makeStraightRebar(50, ("Bottom Side", 20), 100, 100,
                                        12, True, 5, "Horizontal", Structure, "Face4")
Rebar.ViewObject.ShapeColor = (0.9, 0.0, 0.0)

Rebar2 = StraightRebar.makeStraightRebar(50, ("Bottom Side", 50), 100, 100,
                                         12, True, 5, "Horizontal", Structure, "Face6")
Rebar2.ViewObject.ShapeColor = (0.0, 0.0, 0.9)

Example vertical

import Arch, Draft, StraightRebar

Structure2 = Arch.makeStructure(length=1000, width=1000, height=400)
Structure2.ViewObject.Transparency = 80
Draft.move(Structure2, FreeCAD.Vector(1500, 0, 0))
FreeCAD.ActiveDocument.recompute()

Rebar3 = StraightRebar.makeStraightRebar(50, ("Left Side", 20), 100, 100,
                                         12, True, 5, "Vertical", Structure2, "Face4")
Rebar3.ViewObject.ShapeColor = (0.9, 0.5, 0.0)

Rebar4 = StraightRebar.makeStraightRebar(50, ("Left Side", 50), 100, 100,
                                         12, True, 5, "Vertical", Structure2, "Face6")
Rebar4.ViewObject.ShapeColor = (0.0, 0.5, 0.5)

Edition of rebar

editStraightRebar(Rebar, f_cover, coverAlong, rt_cover, lb_cover,
                  diameter, amount_spacing_check, amount_spacing_value, orientation,
                  structure=None, facename=None)

• Rebar is a previously created StraightRebar object.
• The other parameters are the same as required by the makeStraightRebar() function.
• structure and facename may be omitted so that the rebar stays in the original structure.

Example:

import StraightRebar

StraightRebar.editStraightRebar(Rebar, 50, ("Top Side", 20), 100, 100,
                                24, True, 7, "Horizontal")

StraightRebar.editStraightRebar(Rebar2, 50, ("Top Side", 50), 100, 100,
                                24, True, 7, "Horizontal")

StraightRebar.editStraightRebar(Rebar3, 50, ("Right Side", 20), 100, 100,
                                24, True, 7, "Vertical")

StraightRebar.editStraightRebar(Rebar4, 50, ("Right Side", 50), 100, 100,
                                24, True, 7, "Vertical")

BIM

• 2D drafting: Sketch, Line, Polyline, Circle, Arc, Arc by 3 points, Fillet, Ellipse, Polygon, Rectangle, B-spline, Bézier curve, Cubic Bézier curve, Point

---

• 3D/BIM: Project, Site, Building, Level, Space, Wall, Curtain Wall, Column, Beam, Slab, Door, Window, Pipe, Pipe Connector, Stairs, Roof, Panel, Frame, Fence, Truss, Equipment
  • Reinforcement tools: Custom Rebar, Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement
  • Generic 3D tools: Profile, Box, Shape builder..., Facebinder, Objects library, Component, External reference

---

• Annotation: Text, Shape from text, Aligned dimension, Horizontal dimension, Vertical dimension, Leader, Label, Axis, Axes System, Grid, Section Plane, Hatch, Page, View, Shape-based view

---

• Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid, Working Plane Top, Working Plane Front, Working Plane Side

---

• Modify: Move, Copy, Rotate, Clone, Create simple copy, Make compound, Offset, 2D Offset..., Trimex, Join, Split, Scale, Stretch, Draft to sketch, Upgrade, Downgrade, Add component, Remove component, Array, Path array, Polar array, Point array, Cut with plane, Mirror, Extrude..., Difference, Union, Intersection

---

• Manage: BIM Setup..., Views manager, Manage project..., Manage doors and windows..., Manage IFC elements..., Manage IFC quantities..., Manage IFC properties..., Manage classification..., Manage layers..., Material, Schedule, Preflight checks..., Annotation styles...

---

• Utils: Toggle bottom panels, Move to Trash, Working Plane View, Select group, Set slope, Create working plane proxy, Add to construction group, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, Toggle subcomponents, Survey, IFC Diff, IFC explorer, Create IFC spreadsheet..., Image plane, Unclone, Rewire, Glue, Reextrude
  • Panel tools: Panel, Panel Cut, Panel Sheet, Nest
  • Structure tools: Structure, Structural System, Multiple Structures
  • IFC tools: IFC Diff..., IFC Expand, Make IFC project, IfcOpenShell update
  • Nudge: Nudge Switch, Nudge Up, Nudge Down, Nudge Left, Nudge Right, Nudge Rotate Left, Nudge Rotate Right, Nudge Extend, Nudge Shrink

---

• Additional: Preferences, Fine tuning, Import Export Preferences, IFC, DAE, OBJ, JSON, 3DS, SHP

User documentation

• Getting started
• Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
• Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate

---

• Help: Tutorials, Video tutorials
• Workbenches: Std Base, Assembly, BIM, CAM, Draft, FEM, Inspection, Material, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework

---

• Addons: Addon Manager, External workbenches, Scripting and macros

---

• Hubs: User hub, Power users hub, Developer hub